Replaces
Item Condition:
New
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. We've created thousands of videos to help you install our parts with confidence. That saves you time and money, so visit us at 1AAuto.com, your trusted source for quality auto parts.
All right, to find the idler arm on your truck—it's on the passenger side—is to start at the tie rod end and just follow the arm all the way to your inner tie rod and then up to your idler arm. The idler arm is on the passenger side, and it bolts to the frame of the vehicle and to the steering itself. You can watch the play in it by just moving the tire back and forth forcefully with your hand. There shouldn't be any sort of play in between the idler arm and the steering shaft itself. That is actually the problem here. The vehicle failed inspection because there's too much play here. It's actually to a point where it's actually becoming dangerous, because this is actually going to break apart pretty soon. We want to get in here and replace the idler arm.
The first step to removing the idler is removing the cotter pin that holds the nut in place. I think to use a pair of cutters to grab it with. It's usually the easiest thing to do, although I may prove myself wrong. There we go. Then you can also use a pair of locking pliers to pull it from the other side. Then you'll take your 21-millimeter socket with an extension, and I'm using a 1/2 inch ratchet because it's going to be pretty tight, and we'll crack it loose. Luckily it's greasy, so once you crack it loose it usually spins right off.
Ideally, you want to have a puller, which you can get from your local hardware store or auto parts store. You can usually rent them. You'll want to put it on like this. We're using a two jaw puller. It wraps up on both sides of the steering arm, and then the center bolt pushes right on the idler arm. Then in our case it's a 16-millimeter right here, but depending on the puller it could be a different size. At that point, you want to just tighten up your puller until the idler arm breaks free. We're going to be pulling off the idler arm with the idler arm bracket, so we need to take out the lower nut right here and then the upper one right up here.
In New England, we like to spray everything with rust penetrator because we take it off because it just makes life a lot easier. On the front side of the bracket, there's the actually heads of the bolt that we're going to put a socket on. Right here is the lower one. Then up here is the upper one. We're going to use a 21-millimeter with an extension and a little wobble adapter so that we can get on there. It's not the easiest thing to reach, but once you're on there it should stay there. Then on the backside we'll put a wrench to hold the nut in place, and hopefully turn it.
Now we're heading for the top bolt on the idler arm bracket. We have our 21-millimeter wrench on the backside and then 21-millimeter socket and extension on the front. At this point, we'll be able to just pull the whole idler arm and its bracket right out of the truck like so. With the idler arm off the truck, we put it in a vice, and you can see how much movement there is in it. There obviously shouldn't be any. That should be nice and tight.
We've cleaned up our idler arm and idler arm bracket. Both are well used, but we're going to show you how to separate the idler arm from the bracket itself. In our case, there's a 24-millimeter nut on here. That may differ depending on if your car has an original OEM part or if it's been replaced before. In our case, it's 24-millimeter. We're going to throw it in the vice and put our 24 millimeter socket on with a 1/2 inch ratchet because you want plenty or torque, and hopefully we can crack this loose. With the nut off, now we have to pull the idler arm off the idler arm bracket.
Once again I'm going to reposition this in the vice. Get a puller, which you can rent from a local hardware store or an auto parts store, or they're actually not too expensive if you just buy them and you think you might be doing this more than once. It might be worth buying a kit to do this. Then you'll tighten down the center bolt. In our case, we have a 16-millimeter on the top of the puller, which we will once again use our 1/2 inch ratchet to tighten up. You always want to wear your safety glasses when you're doing these things, safety gloves, because things tend to spring off when you're least expecting it, kind of like that. Now that it's broken loose, you can pull it right off.
Here are the idler arms. You can see the old one right here. This one has a ton of play in this section. I think it's probably due to the fact that somebody didn't grease this on a regular basis. Usually, if you put the grease in and then forget about it for the next 100,000 miles, it's going to wear out the inside, and you're going to need to replace the whole thing again. This one obviously comes with a new greaseable fitting on the top. The key is you just want to make sure that you properly grease these on a regular basis, and it'll pretty much last as long as you take care of it. It also does come with a little foam piece on the bottom like the original has. Yeah, it looks, feels, and acts just like the original.
In our case, we're going to be replacing the idler arm bracket and the idler arm, and this is the same process, whether you're replacing one or the other, but we always recommend doing them both at the same time since you have them both out of the vehicle. It's just a really easy thing and it doesn't cost a whole lot more, or a whole lot more money to swap them both at the same time. To do this, we'll hook the idler arm bracket into the vice and we'll slide the idler arm right onto the bracket. Put the nut on there. This happens to be a 24-millimeter. Depending on what kind of part you have in your car, it may vary. The size may vary a little bit.
At this point, we can tighten this up. We started tightening the nut, and we found that the whole thing was spinning, like you can see here. That's why they put a hex on the top of this, so that you can put a wrench here and a wrench on the bottom, and then you can tighten down the nut much easier. While the idler arm bracket and idler arm are out of the vehicle, we're going to put the grease in them. That way it's a little bit easier on us once they're installed. Now we can slide the whole assembly right back in. There's one bolt in place. Now we'll do the lower bolt, which is a little trickier.
All right, with the top, or with the idler arm bracket bolts in place, then you can push the idler arm into the steering and tighten up the castle nut, or hand tighten the castle nut. Now we're going to take our 21-millimeter socket and extension and place it on the upper bolt and put a wrench on the backside. Of course, we want to turn the ratchet in the proper direction, and we'll start tightening up that bolt. All right, then we'll go for the lower one, which again 21-millimeter with a ratchet and extension and 21-millimeter on the back.
Now we have the 21-millimeter idler arm nut that we are going to use a ratchet and extension and socket on. We want to get it tight enough so that it is held in place, but we also want to line up the castle nut with the hole in the idler arm so that we can get the cotter pin through. Now you can slide the cotter pin through the hole and bend it over so that it stays in place. Now you'll see that when we move the wheels back and forth, the play between the idler arm and the steering bracket no longer exists.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
All right, friends, so one of the first things we need to do is safely raise and support the vehicle. Once you've done that, you want to come right up front to this skid plate right here. Go ahead and remove all 15-millimeter bolts that hold it in. Now that that's out of the way, let's come right over here to where the idler arm comes down through this arm right here. Remove the 21-millimeter nut.
Now, the next thing we would need to do to get this arm out of here is, of course, try to drop this sway bar out of the way. If your bolts look like ours do, and you think that they're going to be an issue, I would just skip right past that, and we'll come right up here, and we'll remove the whole idler unit right here. To get this out of here, we're going to use a 21-millimeter right there, and then we'll use a 21-millimeter wrench on the nut side.
Right there. Let's put a nice piece of wood in between the frame and this bar right here just to make it so this bar can't go up too far while we hammer on this right there. Now that that's out of there, we can grab right onto this, and we'll get it out of the vehicle. Now, when you're replacing the idler arm here, you're going to need to separate it from the idler arm bracket assembly. When you go to do that, you're going to remove this nut right here, and then you're going to have to try to get something in between to try to separate.
You could try to use a puller, and that would probably be helpful if you have that tool. If you don't have the tool, and you try using a pickle fork, you're probably going to damage this right here, in which case, you would replace the pair, which is what we're going to do today. But I'll still show you how to get it apart anyways just in case you're doing only one piece.
Now, to remove this, I like to have it nice and level on the ground, and I'll put my foot on it. I'm going to have it so it's facing down towards the left, so when I remove this and it tries to spin, it can't go anywhere. Now, that we have the nut off of there, we need to separate the idler arm from the bracket assembly itself. We want to do that without damaging the bracket assembly because we're going to be reusing it, right?
So if you were to look right up here, you're going to see that there's a hole right inside the center of this. What I would like to do is take a punch. I'm going to put this on something sturdy. You can use something like a piece of wood like I have now, a desk, a vise, anything you want. Just be super careful. Come right in here with your punch and a hammer. Let's see if we can get this to come out.
Okay. So that came out, and we caused no damage to this. Perfect. The next thing I like to do is put the unit right inside of a vise if you have access to one. You want to grab on to this boot. Take a look underneath there. Make sure there's plenty of grease. Go ahead and push it down. That feels great. Now, we're going to take that idler arm. Set it right down on there. Take our brand-new nut. You always want to use a brand-new nut.
Okay. So now if I use my 24-millimeter wrench, and I try to tighten this, what you're probably going to notice is the stud on the inside is going to start spinning once it gets to a certain point. Okay. So as you can see, it's spinning the stud. Is the nut all the way down? No, it's not. So now we're going to use a hex bit, and you want to use an 8-millimeter. Come right inside there. That's going to hold it, and now we'll continue tightening this.
Make sure it's nice and tight. That feels great. Maybe time to get our unit back up inside the vehicle here. Just bring it right up and in behind those lines hopefully. Okay, get that in the center link. Let's get this into its bracket. Okay, that looks decent. Let's grab our two bolts. Make sure that they have washers. Put that right through. The other one. There we are. Let's grab the washers and the nuts for the other side. Now, let's snug these up. Now, let's go ahead and torque these down to 73 foot-pounds.
Torqued. Let's get this nut on there. Snug it up. Torque this to 46 foot-pounds. Torqued. And use our locking cotter pin. Slide it right on through there, and then make sure you pin it over so there's no way this nut can come loose. This out of here. Awesome. Let's get this shield back up on here. I'm going to line up those holes. Start in all the bolts before I tighten any of them down. Perfect. The next thing that I would want to do is make sure that I get it down to a reputable alignment shop.
Tools used
You want to keep in mind when you're doing this job, after you're done, you're gonna want to go to a local garage and have the vehicle aligned so you don't have premature tire wear.
Just take this cover off. Use a 15-millimeter socket. There's two bolts in the bottom, two on top. Sometimes there'll be a third. Slide it off. Take this cotter pin out. Just use some side cutters and pull that up. Just gonna use a little rust penetrant. It's a little rusty. Take a 21-millimeter socket. Take this nut off.
Now, I want to separate the idler arm from the steering bar. I'm just gonna use a front-end tool. There's many different tools you could use to get this off. Just tighten this up. Put the nut on just so my tool doesn't slip off the stud. It's just gonna use it as a guide.
Another way you can try to do this is use a pickle fork. There we go. Slide that up. I'm going to take these two bolts out. I'm going to use a wrench, a 21-millimeter wrench backside to hold the nut. Use a 21-millimeter socket on the bolt. Take both of those out. Pull the bolts out. Let me just grab the whole idler arm assembly and you just slide it off.
If you're gonna replace just the arm or just the assembly, you're gonna have to separate it. So use a 24-millimeter socket. It helps to put it in a vise and then you can use a puller and separate these two just like that. And take the arm, put the new nut on. Just snug that up tight. All right, just line this up.
I'm gonna have to tap this in place. That's good. Before you put the bolts through up top, just make sure it's going through this bar right here. Put the bolts in, take the two nuts. Get them on the back side. Now, snug these up. Torque to 74 foot-pounds. And take the castle nut, install that there, tighten it up and torque this to 46 foot-pounds.
If the hole didn't line up, you can just tighten it up a little bit more so you can put the cotter pin in. Slide the cotter pin in, and just bend one of the tabs over and trim the excess. Take this shield, install it bolts, put the back in, and tighten these up.
Tools used
Normally, there is a shield right here, you wanna take that shield off. There'll be four or five 15-millimeter bolts. Take that off, get it out of your way. Now, we're gonna take this nut off. On this vehicle, there's a cotter pin. So, I'll just use some side cutters, take this cotter pin off. Just bend it back a little bit and just pry it out. And sometimes they break. There we go. Now, I'm gonna take a 22-millimeter socket, take this nut off. Now, I wanna remove that stud from the steering linkage that goes through the idler arm. I'm gonna use a tool like this, it's gonna press it out. You can use a couple other methods. You could use a pickle fork, try to get it out this way...that way. Just gonna put the nut on to stabilize the tool so it doesn't fall off. All right. While that's on there tight, I'm just gonna give it a tap with the air hammer, see if the vibrations loosen it up. So, that didn't work out. So, I'm gonna try a pickle fork. Sometimes these are tricky to get to separate. There we go.
Now, I'm gonna take these two bolts out. I'm gonna use a 21-millimeter wrench. On the backside, there's a nut and then a 21-millimeter socket on the front. Get that nut off. Take the bolt out. And just grab the idler arm and the housing and just slide it up. If you were gonna replace one of these pieces or the other, you can separate that nut. Just gonna put the housing in the vise, make it easier to install. Take the nut off. All right. Take the idler arm, put the nut on, take a 24-millimeter socket and snug it up. Now, I'm gonna take this castle nut off. And get this in position. As you slide the housing in the bracket, you wanna make sure the idler arm goes through the steering linkage. Get the bolts lined up. And put the nuts on the backside. Now, I'll tighten these down. Then torque both of those bolts to 73 foot-pounds. Now, install the castle nut and tighten that up. And then torque this to 46 foot-pounds. And find the hole through the stud and you can use the cotter pin, slide it through. If it doesn't fit or if you can't get it to line up, you can tighten the nut up a little more so it does line up. There we go. And use some side cutters and just bend this like this. And then you can trim the excess. Now, if you have that shield right here, reinstall that shield.
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Idler Arm